去查网 logo

AEI After End of Injection

中文翻译喷射结束后

同义词释义

    1)AEI After End of Injection,喷射结束后2)beam-jetting,聚束喷射3)EOI End of Injection,喷油结束4)injection lag,喷射滞后5)injection structure,喷射结构6)spray-crystal method,喷射结晶

用法例句

    And the rising rate increases rapidly when beam-jetting, and it is higher for fully-path jetting and cylindroconical tube beam-jetting than that for half-path jetting and c.

    若对超声喷泉进行聚束喷射,那么这种温度上升速率显著提高,并且采用全程聚束时高于半程聚束,锥形管聚束时高于柱形管聚束,但无论采用哪种聚束方式喷射,超声喷泉内的温度上升速率均在1min左右趋于饱和。

    The effects of exterior ring and interior ring injection structure on combustion stability are studied in 23 mm RLPG experimental device.

    报道在 2 3mmRLPG试验装置上 ,研究了外环喷射结构和内环喷射结构对燃烧稳定性的影响 ,分析了外环喷射结构对RLPG点火燃烧不一致的原因。

    Heating mechanism of ultrasonic cavitationfield and heating rate while the field is gathering;

    超声空化场的致热机制及其聚束喷射时的致热速率

    beam forming optics

    射束形成光学;聚束光学系统;聚束光学系统

    Disconnect all fuel injection harness connections.

    断开所有的燃油喷射电线束接头。

    Then diesel fuel oil is injected or sprayed into the cylinder at the end of the compression stroke.

    然后在压缩冲程即将结束时,柴油燃料被喷射或被喷雾进入气缸。

    Experimental Study of Hybrid Processing of Jet Electrochemical Machining and Laser Beam Machining

    喷射液束电解-激光复合加工工艺试验研究

    Feasibility Study of Hybrid Processing of Laser Beam Machining Combined with Jet Electrochemical Machining

    喷射液束电解—激光复合加工可行性研究

    Progress in Technology of Focus Microwave Energy in Hyperthermia

    微波热疗辐射器聚束方法的研究进展

    The Study about Polyacrylic Fiber Concrete Used in Anchor Arm-shotcreting Support of Tunnel;

    聚丙烯纤维喷射混凝土在隧道锚喷支护中的应用研究

    This is jet bit and that is a PDC bit.

    这是喷射式钻头,那是人造聚晶金钢石钻头。

    Plastics--Vinyl chloride homopolymer and copolymer resins Sieve analysis using air-jet sieve apparatus

    GB/T2916-1997塑料--氯乙烯均聚和共聚树脂--用空气喷射筛装置的筛分析

    Ejection murmurs begin after S1 and are usually crescendo-decrescendo(" diamond-shaped'), ending before S2.

    喷射音始于S1后,通常有渐强-渐弱特征,并于S2前结束。

    Study on the Mechanism and Surface Characteristic for Abrasive Jet Precision Finishing with Grinding Wheel as Restraint;

    砂轮约束磨粒喷射精密光整加工机理及表面特性的研究

    3D Profile and Generating Mechanism of Cylindrical Surface Lapping Machined with Abrasive Jet Flow Restricted by Grinding Wheel

    砂轮约束磨粒喷射加工外圆表面创成机理及三维形貌

    The Fractal Dimension and Tribological Characteristic Investigation of Finishing Surfaces for Abrasive Jet Finishing Restricted by Grinding Wheel

    砂轮约束磨粒喷射加工表面的分形及摩擦特性研究

    Experimental Study of Hybrid Processing of Jet Electrochemical Machining and Laser Beam Machining on Nickel-based Superalloy

    镍基高温合金喷射液束电解-激光复合加工试验研究

    Residual Stress and Tribological Characteristics of Ground Surface After Abrasive Jet Restricted by Grinding Wheel

    砂轮约束磨粒喷射加工表面残余应力及摩擦特性

    The Fractal Dimension of Cylindrical Surfaces for Abrasive Jet Finishing Restricted by Grinding Wheel

    砂轮约束磨粒喷射精密光整加工外圆表面分形维数的研究

    Self-Focusing of Gaussian Beams in Graded-Index Media with Kerr Nonlinearity;

    高斯光束在梯度折射率Kerr介质中的自聚焦

全部查询工具

关于我们免责声明联系我们网站地图最近更新

免责说明:本站为非营利性网站,本站内容全部由《去查网》从互联网搜集编辑整理而成,版权归原作者所有,如有冒犯,请联系我们删除。

Copyright © 2020 - 2024 quchaw.com All rights reserved.浙ICP备20019715号