去查网 logo

Offset of edges of plates at joints

中文翻译在接头处板边的偏差

同义词释义

    1)Offset of edges of plates at joints,在接头处板边的偏差2)fset of plate edges at joints,连接处板边的偏移3)pressure expanded joint,板边胀接接头4)anterolateral,在前面偏一边的5)holes in joints of,接头处的孔6)edge board connector,板边插头,板边连接器

用法例句

    holes in joints of welded vessels

    焊接容器接头处的孔

    openings through welded joints

    通过焊接连接处的开孔

    Pull the switch out from the mounting hole in the door opening far enough to access the wire harness connector.

    从车门洞里的固定孔中将开关拉出足够远,以便能处理线束接头。

    Make four indentations into the condenser near the standard cone joint.

    在冷凝器接近标准圆锥接头处打四个穴孔。

    Discussion on Heat Treatment of 3Cr2W8V Three Rolls Punching Stamp

    3Cr2W8V钢制三辊穿孔顶头的热处理探讨

    hydraulic gun release sub

    射孔器水力丢手接头

    plug-and-jack type connector

    插头-插孔式连接器

    automatic gun release sub

    射孔器自动丢手接头

    RIGHT DOOR KEY CYLINDER SWITCH CONNECTOR

    右门钥匙插孔开关接头

    Heat Treatment Strengthening of Al─Li Alloy 2091 Welded Joint

    2091铝锂合金焊接接头的热处理强化

    Slag, blowholes, and paint on unfused regions were observed at the welded junctions.

    在焊接处看到了夹渣,气孔及未熔透区的油漆。

    3-D Elastic and Plastic FEM Analysis of Hydraulically Expanded Tube-to-Tubesheet Joints with Tubesheet Hole Groove;

    管板孔开槽的液压胀接接头三维弹塑性有限元分析

    Application of Improved Blind Hole Method to Welded Iron Tower Joint for Stress Relieving with Heat Aging

    改进型盲孔法在铁塔焊接接头热时效消除应力中的应用

    Bring a comb, charged by combing hair, near to a tap in the dark.

    把梳过头而带电的梳子靠近黑暗处的电线接头。

    USING AN OHMMETER MEASURE GROUND CKT AT BLUE CONN

    用欧姆表测蓝色接头处的地电路

    Broken connector terminal or wire splice in fog lamp circuit.

    雾灯电路的接头端子或电线熔接处断裂。

    Fatigue Performance Improvement of 22SiMn2TiB Steel Welded Joint by Ultrasonic Impact Treatment

    超声冲击处理改善22SiMn2TiB钢焊接接头的疲劳性能

    Effect of Postweld Heat-treatment on Microstructure and Mechnical Properties of BHW35 Steel Welded Joint

    焊后热处理对BHW35钢焊接接头组织性能的影响

全部查询工具

关于我们免责声明联系我们网站地图最近更新

免责说明:本站为非营利性网站,本站内容全部由《去查网》从互联网搜集编辑整理而成,版权归原作者所有,如有冒犯,请联系我们删除。

Copyright © 2020 - 2024 quchaw.com All rights reserved.浙ICP备20019715号