TP Throttle Position(sensor)

用法例句

The control switch on-off mode of automotive fault simulation test bench is used to simulate the signal of the air throttle position sensor and measure the parameters related to the engine performance and emission.

利用汽车故障模拟台的控制开关通断来模拟节气门位置传感器信号的有无,同时测量与发动机性能和排放等有关的参数,进而分析该传感器某些功能失效对发动机的影响,正确地检测出发动机的故障。

The author analyzes common ways to inspect the air throttle position sensors of linear variable resistor switching and decoding.

对线性可变电阻型、开关型、编码型节气门位置传感器常用的检修方法进行分析和探讨。

The influences of the signal of full charge throttle position sensor on the capacity of engine is studied on the electronic controlled gasoline injection engine of VOLVO B230F.

通过在VOLVOB230F型电控汽油喷射发动机上研究节气门位置传感器的全负荷信号对发动机性能的影响,并对节气门位置传感器故障造成的发动机性能变化的对比可分析表明:节气门位置传感器的全负荷信号丢失以后,混合气变稀,功率下降;CO和HC排放降低,NOx排放升高,同时有助于指出了节气门位置传感器在电控发动机故障诊断中的作用。

The paper, according to the specific structure of motorcycle throttle, analyzed the research results of throttle position sensor to identify the deficiencies of the design program in the linear range and improves the design program of Hall Effect throttle position sensor; then simulated the program with FEMM that is two-dimensional finite elemen

节气门位置传感器简称TPS,它是喷油量、点火提前角等控制参数和怠速、起步、加速等过程控制的主要信号源。

After analyzing the basic principle and structure traits of Auto Cruise Control System(CCS) and defining input signals and output signals,A CCS simulant equipment was built up,We brought forward a kind of new control scheme which is that Dual closed-loop controlling method of auto speed and throttle threshold is adopted and controlling arithmetic is parameter adaptive PI.

分析了巡航控制系统(CCS)的基本原理和结构特点,确定了输入输出信号后,搭建了巡航模拟实验台,提出了一种新型巡航控制系统设计方案,即对转速、节气门开度双闭环控制,运用参数自适应PI控制算法,可以不断智能调节比例和积分参数,从而改善控制效果。

Research on Hall Effect Throttle Position Sensor and Speed Sensor for Motorcycle

摩托车用霍尔效应节气门位置传感器和转速传感器的研究

position sensor

位置检测器位置传感器

Manual Valve Lever Position Sensor

手动气门叉杆位置感知器

Throttle Body and Sensor Locations—Engine

节气阀体与感知器位置—0L引擎

Throttle Position Sensor Mounting Screws

节气阀位置感知器固定螺丝

Supplies the required 5 volt power source to the crankshaft position sensor, camshaft position sensor, MAP sensor and throttle position sensor.

向曲轴位置感应器、凸轮轴位置感应器、MAP感应器以及节气阀位置感应器提供所需的5伏电压。

Valve position transmitter based on the linear Hall sensor

基于线性霍尔传感器的阀门位置变送器

Development of novel robot joint position sensor

一种新型机器人关节位置传感器的研制

Research on Running Control of Elevator s Door Without Position Sensors;

无位置传感器的电梯门机运动控制研究

The Research on Energy-efficient Algorithms Based on Position Information in Sensor Networks;

传感器网络中基于位置信息的节能算法研究

Location-independent Coverage-preserving Algorithm for Sensor Networks

传感器网络中与节点位置无关的覆盖算法

Optimal Sensor Deployment Based on Secure Connection in Mobile Sensor Network

移动传感器网络基于安全连接的节点位置优化

angular position type density sensor

角度位置式密度传感器

position sensing photodetector

位置传感光电探测器

Research and Implementation of Location Independent Node Scheduling Algorithm for Sensor Networks;

无位置信息传感器网络节点调度算法研究与实现

The adjusting of screw prevents the throttle valve from moving to the fully closed position.

调节螺钉防止节气门运动到全关闭位置。

Accelerator Pedal Postion Sensor Signal High Exceeded

油门踏板位置感知器信号过高

This circuit supplies approximately 5 volts to power the Accelerator Pedal Postion Sensor, and Mass Air Flow Sensor.

该电路为油门踏板位置感知器和气流感知器提供大约5伏的电源电压。