angle of taper

用法例句

The results show that the tapping torque with a modified tooth tap can be greatly reduced compared to that with a standard tap, and the better machining effect can be achieved by using a modified tooth tap with a bigger cutting cone angle.

试验结果表明 ,与标准丝锥相比 ,采用修正齿丝锥可显著减小攻丝扭矩 ,且切削锥角较大的修正齿丝锥加工效果较

Unfortunately the ratio of undercutting rate to etching rate of(100)crystal plane in 40% KOH solution is about 1.

然而在40%KOH溶液中削角速率和(100)晶面的腐蚀速率之比约为1。

Unfortunately the homogeneity of undercutting silicon tips is bad,and the etching ratio of(100) crystal plane to that of undercutting rate is small.

通过在KOH溶液中添加过饱和的碘单质(I2),显著减小了快腐蚀面的削角速率,在较小的掩膜下腐蚀出高的硅尖。

Analysis of Array Antenna Pattern Amplitude in Uniform and Taper Distribution

阵列天线幅度均匀分布和锥削分布方向图分析

Aerodynamic analysis for a reentry vehicle with slice-flaps

带控制舵钝双锥削面体的气动特性研究

Research on Grinding the Convexity of Taper Roller Conical Surface Lines via Centerless Grinder

无心磨床磨削圆锥滚子圆锥面素线凸度的研究

Processing Method of Screw for Conical Twin-screw Extruder

锥形双螺杆削挤出机螺杆的加工方法

Vibration-prevention Lathing Process for Long Shaft Circumference of Tapered Spiral Blades

锥形螺旋叶片长轴外圆防振车削工艺

Analysis on Working Angle of Scraping Cutter for Bevel Gear with Circular Arc Teeth

弧齿锥齿轮刮削刀盘工作角度的分析(上)

Tooth Contact Analysis and Cutting Parameters Modification of Small-modulus Spiral Bevel Gears;

小模数弧齿锥齿轮的接触分析与切削参数修正

Discussing based on cutting method of conical cylinder with plane arc axes;

平面大圆弧轴线圆锥柱体切削机理研讨

Research on Generation Mechanism and Correction Technique for Spiral Bevel Gear's Grinding Errors

螺旋锥齿轮磨削误差产生机制及修正技术研究

Analyzation and application of turning method for tapered roller bearing inner ring raceway

圆锥滚子轴承内圈滚道车削方法的分析及应用

Research on Surface Roughness for Multi-axis NC Grinding of Spiral Bevel Gear

多轴数控磨削螺旋锥齿轮的表面粗糙度研究

Based on NC Turning Screw Cone Programming Method

基于数控车削的圆锥螺纹编程方法研究

Research on Surface Roughness for Multi-Axis NC Grinding of Bevel Gearr

螺旋锥齿轮数控磨削表面粗糙度的建模与分析

The Optimized Design and Reshaping of Profile of Skiving Cutter with Plane Flank for Gleason Gear;

弧齿锥齿轮尖齿刮削刀盘的齿形优化设计与重磨

Surface Roughness Forecasting of Spiral Bevel Gear Based on Artificial Neural Network

基于人工神经网络的螺旋锥齿轮磨削加工表面粗糙度预测

For grinding HSS and carbide engraving cutter as well as single lip or multiple lip cutters of various shapes such as radiuses cutters or negative taper angle of cutters.

该机可用于磨削各类形似半圆角或反锥角的高速钢和硬质合金雕刻刀具和单边或多边刀具。

The metering rod either has two or more steps of different diameters or is tapered at its lower end.

量油杆可以有两个或更多个不同直径的台阶，或在它的下端被逐渐削成锥形。

"Suitable corrective measures must be taken to remove these obstructions, such as taper boring the pipe or installing a spacer."

这是就要进行必要的矫正,例如对管道口进行锥形切削,或安装隔离垫圈,以消除这些障碍。