bearing pressure bolt
同义词释义
- 1)bearing pressure bolt,轴承的压紧螺栓2)holding down bolt,轴承紧固螺栓3)bearing,轴承螺栓4)pinion bearing retainer bolt,小齿轮轴承夹紧螺栓5)press(ure) bolt,压紧螺栓6)bearing block bolts,轴承座螺栓
用法例句
The defomations of synchroshaft of step cooling bed in the plant causes the bearing block bolts broken and the inner wall of lift cylinder serously and eccentriclly worn.
涟钢三炼钢厂1#步进冷床下降速度慢且不能到达终点、轴承座螺栓断裂和升降油缸内 壁严重偏磨的主要原因是同步轴严重变形,本文针对同步轴变形提出了改进措施。
Contact analysis of MW wind turbine hub and bearing bolt connection
风力机轮毂和轴承螺栓联接接触分析
The Fracture Failure Analysis on Main Bearing Bolts of the Diesel Engine and Investigation on Its Loading Behaviours;
柴油机主轴承螺栓断裂及其承载力学行为的研究
Bolt( screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.
螺栓(钉、帽、头螺栓、簧垫圈、、珠轴承、柱轴承)最常用的机械零件。
377 bolt (screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.
螺栓(螺钉、螺帽、双头螺栓、弹簧垫圈、销、滚珠轴承、滚柱轴承)是最常用的机械零件。
Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.
在轴壳内(没有垫片)安装差速箱和模型轴承,并紧固固定帽螺栓。
hydrauliccone-bolt coupling
液力锥形螺栓联轴器
Research and Design on the Backpressure Device and Bolt Assembly System in the Fracture Splitting Equipment of Main Bearing Walls on an Engine Block;
缸体主轴承座裂解加工背压装置及螺栓装配系统研制
Research and Design on Automatic Assembling Bolts System for Fracture Splitting Crankcase Bearing Block of Engine;
裂解发动机箱体主轴承座螺栓装配系统研究与设计
Plain Bearing Block Housings are made up of cap, base ,aluminum bronze bushing and installing bolts, which mainly bear radial load.
滑动轴承座由上盖、底座、剖分轴瓦(铝青铜),安装螺栓组成,主要承受径向载荷。
Remove nuts, U-bolts and spring bracket from axle.
由车轴拆下螺帽,U型螺栓和弹簧支架。
Front Stub Axle To Hub Bearing Nut
前螺桩轴至轮毂轴承螺帽
Research on the Influences of Internal Oblique Nut on Bolt Bearing Capacity
内斜螺母对螺栓承载能力影响的研究
spring seat bearing adjusting nut
弹簧座轴承调整螺母
wheel hub bearing adjusting nut
车轮毂轴承调整螺母
Lock rings at the end of shaft with bolt
GB/T892-1986螺栓紧固轴端挡圈
Bushing Retainer To Axle Attaching Bolts
衬套扣环与车轴接合螺栓
Remove vibration damper bolt and washer from end of crankshaft.
从曲轴端拆下减震器螺栓和垫圈。
Tie Rod End Adjusting Sleeve Nut
转向拉杆端调整轴筒螺栓
相关英语词汇
- Business management是什么意思
- barbierite是什么意思
- brake application是什么意思
- bench molding是什么意思
- boost calibration是什么意思
- bursting expansion是什么意思
- bell manometer是什么意思
- bus error recovery是什么意思
- blank carburizing是什么意思
- blink rate是什么意思
- brake lining friction material是什么意思
- blood group system (blood group)是什么意思
- briefly farozen soil是什么意思
- Branchial clefts是什么意思
- biochemigenic rock是什么意思
- byte instructions是什么意思
- beating the market是什么意思
- bank是什么意思
- biochemorphology是什么意思
- BOC Bus Out Check是什么意思
- bivariate是什么意思
- bead method是什么意思
- bench stoping是什么意思
- benzine是什么意思
- bacteriopheophytin (Bpheo)是什么意思
- Blood lead (Bpb)是什么意思
- bright stock是什么意思
- bulk defects是什么意思
- bevel gear backlash是什么意思
- buried anomaly是什么意思