bearing water supply line

用法例句

In this paper,the advantages for construction of thrust bearings,turbine guide bearings,main shaft seal,runner seal are analyzed.

通过运行实践 ,本文对该水轮发电机组的推力轴承、水导轴承、主轴密封、转轮密封等主要结构进行了分析 ,仅供参考。

Research on water pump bearing clearance measuring mechanism;

水泵轴承径向游隙加载测量机构的研制

Welds repair of the bush of water flowing diversion bearing of the hydro-generator unit

水轮发电机组水导轴承轴瓦的焊接修复

Lubrication Performance Study on Guide Bearing for Hydropower Sets;

水轮发电机组水导轴承润滑性能分析

The Installation and Test of the Hydraulic Turbine Guide Bearing of Three Gorges Right Bank Power Station

三峡右岸机组水导轴承安装及调试特点

Direct Solution Method for Load Force and Jacobi Matrix of Water Guide Bearing in Turbulent Regime

湍流工况下水导轴承承载力及其Jacobi矩阵的一维直接算法

Research and Application of Improving Scheme for Circulating Pump Guide Bearing in M701F Gas-steam Combined Cycle Unit

M701F型燃气-蒸汽联合循环机组循环水泵水导轴承改进方案研究及应用

The Determination of the Critical Technical Supply Pressure of the Rubber Guide Bearing of the Axial Pump

轴流泵橡胶导轴承技术供水临界压力的确定

As lubricated with outside clean water, bearings are of long life.

导轴承由外接清洁水润滑，使用寿命长。

Dynamic Coefficients of Tilting Pad Guide Bea-rings of Hydraulic Turbine Sets, Power Engineering

水电机组可倾瓦导轴承动力特性系数

The slide bearing assembled in middle segment is separated from sewage by inside pipe.

中间节设有由内导管将污水隔离的滑动导轴承。

Treatment on oil throw fault in lower guide bearing of generator of Shuibuya Hydropower Plant

水布垭水电站发电机下导轴承甩油问题处置

Improvement on guide bearing and seal set of propeller turbine of Huangxi Hydropower Station

黄西水电站水轮机导轴承和密封的改进

Guide bearing of vertical hydrogenerator carries the radial force from its rotatory parts.

立式水轮发电机的导轴承承受转动部件的径向力。

The carriage is supported on guide shafts.

托架支承在导轴上。

Production and application of thrust bearing,and guide bearing made of filled PTFE in submarine motor pump are introduced.

介绍了潜水泵中止推轴承与导向轴承用填充聚四氟乙烯材料进行的生产和应用。

Leakage Cause Analysis and Modification of Cooler for 2# Unit's Upper Guide Bearing at Longtan Hydropower Station

龙滩水电站2号机组上导轴承冷却器漏水原因分析及改造

Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.

曲轴上的导向轴承:曲轴上的导向轴承一般或者是轴瓦,或者是球轴承。

Lightly lubricate pilot bearing with Mopar® high temperature bearing grease.

用Mopar®高温轴承黄油轻轻地润滑引导轴承。

Discussion on the Hydraulic Parameters of Bearing Prong in Long-axial Pump for Deep Well;

长轴深井泵轴承支架水力参数的探讨