constant pressrue exhaust manifold

用法例句

Converse development on automobile exhaust manifold based on reverse seeking technology of curved surface;

基于曲面反求技术的汽车排气歧管逆向开发

Numerical simulation of thermal loads for engine exhaust manifold;

发动机排气歧管热负荷数值模拟

Thermal Stress Analysis of ICE Exhaust Manifold;

内燃机排气歧管热应力分析

This paper establishes geometric models and finite element models of a car engine exhaust manifold cover,carries out modal analysis,verifies the correctness of the finite element model,analyzes the harmonic response of the manifold cover,determines that the free edges of the manifold cover affects the noise radiation most,and provides the corresponding measures of improvement.

建立了汽车发动机排气歧管罩的几何模型和有限元模型,然后进行模态分析,并通过实验验证了有限元模型的正确性。

The exhaust manifold cover is the main source of surface radiate noise of a 6 360 vehicle s engine.

排气歧管罩是某6360汽车发动机的主要表面噪声辐射源,利用有限元分析技术建立了其有限元模型并进行解析模态分析,分析结果与实验基本一致。

Disconnect the exhaust pipe at the exhaust manifol

断开排气歧管的排气管。

The gases pass into the exhaust manifold.

这些废气进入排气歧管。

exhaust manifold heat control valve

排气歧管热量控制阀

Remove exhaust manifold heat shiel

拆下排气歧管隔热罩。

Disconnect the exhaust pipe at the engine exhaust manifol

拆开引擎排气歧管处的排气管。

Connect the exhaust pipe to the hanger and to the engine exhaust manifol

连接排气管到悬挂物、到引擎排气歧管。

The exhaust gas exits through the other exhaust manifold.

废气经另外一个排气歧管排出。

The basic exhaust system consists of an engine exhaust manifold, exhaust pipe, exhaust heat shield(s), muffler and exhaust tailpipe

基本排气系统包括一个引擎排气歧管、排气管道、排气隔热罩、消音器和排气尾管

Clean the exhaust manifold and cylinder head mating surfaces.

清洁排气歧管和汽缸头配合面。

Remove intake, exhaust manifold and turbocharger, refer to Group 11, Exhaust System and Intake Manifol

拆下进气，排气歧管和透平增压器，请参阅单元11，排放系统和进气歧管。

Optimization Design of Engine Exhaust Manifold Based on Finite Element Analysis

基于有限元分析的发动机排气歧管优化设计

CFD & FEA coupling analysis application in exhaust manifold analysis

某发动机排气歧管流固耦合分析的应用

Couple CFD-FE-Analysis for a Gasoline Engine Exhaust Manifold of Thermal Load

CFD-FE耦合计算分析某汽油机排气歧管热负荷

Numerical Simulation and Experimental Investigation for Sand Casting of Exhaust Manifold Based on AnyCasting

基于AnyCasting排气歧管砂型铸造数值模拟及试验研究

High temperature oxidation cracking analysis of exhaust manifold made of high Si-Mo nodular cast iron

高硅钼球铁排气歧管高温氧化开裂原因分析

Disconnect exhaust pipe at manifol

在歧管处断开排气管。

Install the intake manifold (refer to Group 11, Exhaust System and Intake Manifold).

安装进气歧管（见单元11-排气系统和进气歧管）。

Remove the intake manifold (refer to Group 11, Exhaust System and Intake Manifold).

拆下进气歧管（见单元11-排气系统和进气歧管）。