去查网 logo

crankshaft front end

中文翻译曲轴前端

同义词释义

    1)crankshaft front end,曲轴前端2)front-end of spindle,主轴前端3)crankshaft big end,曲轴大端4)crankshaft end,曲轴端5)crankshaft face,曲轴端面6)crankshaft front bearing,曲轴前轴承

用法例句

    Study of Crankshaft Free End Structure of YC6105ZLQ Diesel Engine;

    YC6105ZLQ柴油机曲轴前端结构研究

    At the rear end of the crankshaft is attached the flywheel, and at the front end are the driving wheels for the timing gears, fan, cooling water and alternator.

    曲轴的后端连接着飞轮,前端是连接着定时齿轮,风扇,冷却水和交流发电机的驱动轮。

    Install new front crankshaft oil seal.

    安装新的前曲轴油封。

    Remove and discard the front crankshaft oil seal.

    拆下并抛弃曲轴前油封。

    Remove vibration damper bolt and washer from end of crankshaft.

    从曲轴端拆下减震器螺栓和垫圈。

    Measuring deflection of crank shaft of M.E. before starting up(after sea trial).

    主机动车前(航行试验后)曲轴甩档测量。

    Pry the crankshaft forward, position the dial indicator to zero.

    向前撬曲轴,定位针盘指示表到0。

    The main bearing journals fit into the cylinder block and the big end journals align with the connecting rods.

    主要轴承曲颈安装在气缸体和与连杆大头末端匹配的曲颈上。

    crankshaft (main journal turning lathe)

    曲轴(主轴颈)车床

    upper center crankshaft bearing

    曲轴主轴承上中轴瓦

    Permanently sealed and lubricated ball bearings front and rear.

    前后端盖装有永久密封和自润滑的滚珠轴承。

    Check the deflection of the crankshaft both before and after repair.

    在修理前和修理后都要检查曲轴的变形情况。

    FE Simulation of Automobile Forward Shaft on Bending Forming and Whole Final Forging Procedure;

    汽车前轴锻件弯曲与整体终锻过程有限元模拟

    "The cylinder of an internal-combustion engine is closed at one end by a plate called the head and open at the other end to permit free oscillation of the connecting rod, which joins the piston to the crankshaft."

    内燃机的汽缸在一端用盖封住,叫做头,另一端敞开,使连接活塞和曲轴的连杆能自由摆动。

    One of the jobs of PCV system is to remove these crankcase contaminants before the rotating crankshaft mixes them with the oil.

    PCV系统的作用之一是,在旋转的曲轴把水和液体汽油混合之前,把它们排出曲轴箱。

    The throw of the crankshaft, i.e. the distance between the main journal and the big end centers, controls the length of the stroke.

    曲轴的摆幅,即在主要曲颈和连杆大头末端中心之间的距离,控制着冲程的行程。

    "On many engines, the connection-rod and main bearings (crankshaft bearings) can be checked for wear with an oil-leak detector before the engine is torn down."

    许多发动机在拆卸之前,可以用漏油检测装置检查连杆和主轴承(曲轴轴承)的磨损情况。

    crankshaft journal face hardening machine

    曲轴轴颈表面淬火机床

全部查询工具

关于我们免责声明联系我们网站地图最近更新

免责说明:本站为非营利性网站,本站内容全部由《去查网》从互联网搜集编辑整理而成,版权归原作者所有,如有冒犯,请联系我们删除。

Copyright © 2020 - 2024 quchaw.com All rights reserved.浙ICP备20019715号