去查网 logo

gusset at margin plate

中文翻译缘板扣板

同义词释义

    1)gusset at margin plate,缘板扣板2)buckle plate,扣板3)platform,缘板4)plate marginal,板缘5)bracket panel,肘板缘板6)floor flange,肋板缘板

用法例句

    A simplified method using transfer matrix method was applied to the analysis and calculation of the vibration damping effect induced by dry friction snubber on the blade platform.

    针对在叶片缘板部位设置干摩擦阻尼块后的叶片减振效果问题,进行理论模型简化后,利用传递矩阵法进行分析计算。

    In order to decrease the vibration of a blade,a dry friction damper is installed on a blade platform to introduce attached damp.

    为了减小叶片振动,在叶片缘板部位设置干摩擦阻尼器,以引入外加阻尼。

    The hunter pulled the trigger and stopped the deer in his tracks.

    猎人扣板机,鹿应声而倒。

    The marksman squeezed off successive rounds and every shot told.

    射击运动员连扣板机,弹无虚发。

    The hunter pulled the trigger and stopped the deer cold.

    猎人一扣板机,鹿应声倒地。

    The hunter squeezed off and down went the furious tiger.

    猎人一扣板机,狂怒的老虎应声倒地。

    To fire the gun, pull the trigger.

    要开枪就扣动板机。

    Position striker on B-pillar.

    将扣击板安放在B-柱上。

    The soldier pressed the trigger of his gun.

    战士扣动枪的板机。

    The Insulation Layer of Nickel Buckles Anode Plate Manufacture and the Design of Nickel Buckles Peel Equipment;

    镍扣种板表面绝缘层的制备及种板剥扣设备的设计

    This shot was bad, not mortal.

    迈克尔向他微笑着扣动了板机。

    Horizontal intermediate cross rails, which are required for locks, will be recessed and concealed.

    水平过渡交叉挡板应扣住,凹入并隐藏。

    CAUTION: NEVER REMOVE SHAFT LOCK PLATE RETAINER

    注意:切勿移动轴锁止板扣件

    Her salary was cut short by her boss without any excuse.

    她的工资无端被老板克扣。

    Separate striker and spacer from vehicle.

    从车辆上拆下扣击板和垫片。

    Remove the push-in fastener from the top of the fan shrou

    从风扇围板顶部拆下压入扣件。

    The boss docked a third of my wages.

    老板扣掉我三分之一工资。

    Study on Ultimate Bearing Capacity of Fastener-style Tubular Steel Falsework

    扣件式钢管模板支架极限承载力研究

    Analysis of Super-High Fastener-style Steel Pipe Formwork Support system

    扣件式钢管模板高支撑体系性能分析

    Press the cowl top trim panel down until the snap clip retainers engage in the top of the instrument panel.

    向下压仪表板顶部饰板,直至夹扣定位器啮合到仪表板顶部。

全部查询工具

关于我们免责声明联系我们网站地图最近更新

免责说明:本站为非营利性网站,本站内容全部由《去查网》从互联网搜集编辑整理而成,版权归原作者所有,如有冒犯,请联系我们删除。

Copyright © 2020 - 2024 quchaw.com All rights reserved.浙ICP备20019715号