hybrid injection locking

用法例句

Clock extration experiment based on the injection mode-locking laser is conducted.

利用注入锁模光纤激光器进行时钟提取实验,成功地从40 Gb/s伪随机码信号中提取出了40 GHz时钟信号。

In this thesis, injection mode locked laser (IMLL) based on semiconductor optical amplifier (SOA) is applied for all optical clock recovery because of its advantages, such as simple configuration, wavelength tunability, stability, low cost and commercially available product, etc.

论文建立了一套比较完善的基于SOA注入锁模激光器的数值模拟模型,系统研究了外界信号、SOA的噪声等参数对时钟提取的影响。

Investigations on Characteristics and Applications of Injection Mode-locked Laser Based on SOA;

基于SOA的注入锁模光纤环激光器特性及应用研究

Injection locked local oscillator

注入锁定本地振荡器

Based on the nonlinear of synchronized oscillators, the expression of locking range for fundamental wave injection locked2 nd harmonic Gunn Oscillators is derived.

本文基于同步振荡器的非线性模型，导出了基波注入锁定二次谐波耿氏振荡器的锁定带宽表达式。

RESEARCH ON MOULD CLOSNG AND LOCKNG FORCE CONTROL OF ELECTRC NJECTON MOLDNG MACHNE

全电子注塑机的合模控制及锁模力的研究

The Extension of Injection Locking Theory and Its Dynamical Behavior Analysis;

注入锁定理论的延拓及其动态行为分析

Extra-cavity mutual injection phase-locking of two fiber lasers

两路光纤激光器外腔式互注入锁相实验研究

Mutual injection phase-locking of two double clad fiber lasers

两路双包层光纤激光器互注入锁相实验研究

The analog input signal is latched on the rising edge of CLK.

模拟输入信号在CLK的上升沿被锁存。

Design of Injection Mold for Trunk Lock's Principal Part of Saloon Car

豪华客车行李箱锁主体部件注射模设计

The hole in a lock into which a key fits.

锁眼插入钥匙的锁的孔

Locksmiths inject graphite powder into keyways to lubricate locking mechanisms.

锁匠会在钥匙孔里注入石墨粉 来润滑阻塞的装置

The experimental researches of fundamental wave injection locked2 nd harmonic Gunn oscillators in3 mm band are completed.

完成了三毫米波段第二次谐波振荡器的基波注入锁定实验。

Hydrogen pressure dependence of stimulated Raman scattering pumped by an injection locking excimer laser

注入锁定准分子激光泵浦下氢受激喇曼散射的气压特性

Studies on Mutual Injection-locking of Fiber Lasers and Post-processing Techniques of Photonic Crystal Fibers

光纤激光器的相互注入锁定和光子晶体光纤的后处理技术研究

The molten metal may enter the ingot mould in two ways: from the top and from the bottom.

钢液注入钢锭模可采用两种方式:上注和下注。

Injection Efficiency of Direct Injection Mode Optical Sensors

直接注入模式可见光和红外传感器的注入效率

Performance Characteristics and Clamping Force Accuracy of Internal Circulation Two-Plate Injection Molding Machine

全液压内循环二板式注塑机性能特点及锁模精度研究

Please see to it that the door is locked.

请注意一下门锁了没有。