isothermal forging

用法例句

Design of heating device for magnesium alloy isothermal forging and temperature curve of die;

镁合金等温锻造加热装置的设计及模具温度曲线

Numerical simulation of grain size during isothermal forging of TC6 alloy;

TC6合金等温锻造过程中晶粒尺寸的数值模拟

Simulation of Isothermal Forging for Superalloy and Analysis of Thermal Load on Die;

粉末高温合金盘件等温锻造模拟及模具热负荷分析

Using TA5 ingot with α/α+β transformation temperature of 990-1 000 ℃ by two times melting,the tests for forging temperature and reduction were performed.

采用二次真空熔炼熔铸的α/α+β转变温度为990￣1000℃的TA5钛合金,在β相区开坯,经多火次中间锻造后,对其最后一火次的锻造,改变锻造温度和变形量共8种工艺方案进行实验,考察锻造温度和变形率对组织和性能的影响。

According to the forging blank requirements of a magnesium alloy shell,the parameters such as forging temperature,furnace holding time,clamping board temperature of the forging machine,forging time and so on of MB2 magnesium alloy forged on the general forging machine are determined by experiments.

根据某壳体零件锻造毛坯的要求,通过试验确定了MB2镁合金在普通锻床上锻造时的锻造温度、炉膛保温时间、锻床夹板温度、锻打时间等工艺参数,为制订该合金的锻造工艺提供了依据。

Analysis of familiar defects of low-temperature forging on operating instruments;

手术器械低温锻造常见缺陷原因分析

Study on Isothermal Forging Techniques and After-forging Structure of Superplasticity of Titanium Alloys;

钛合金超塑性等温锻造工艺及锻后组织研究

Study on Optimization of Isothermal Forging Process Parameter of TA15 Titanium Alloy;

TA15钛合金等温锻造工艺参数优化研究

Research and Development of the Control System for an 80MN Isothermal Forging Hydraulic Press;

80MN等温锻造液压机控制系统研制

Development of a Die Material for Iso-thermal Forging at 1100℃

1100℃等温锻造用模具材料的研制

Near-Isothermal Forging Technology of TA15 Titanium Alloy Corbel Piece

TA15钛合金支臂近等温锻造工艺

Study on Soft-sensor Technology and Inferential Control of Temperature in Isothermal Forging;

等温锻造过程中温度软测量技术与推断控制

Influence of Isothermal Forging Temperature on Microstructure and Mechanical Property of 2A70 Aluminum Alloy

等温锻造温度对2A70铝合金组织性能的影响

Influence of Isothermal Forging Temperature on Microstructure and Mechanical Property of 7050 Aluminum Alloy

等温锻造温度对7050铝合金组织与性能的影响

Numerical Simulation for the Isothermal Forging Processes of Complex Structural Component of Ti-1023 Alloy;

Ti-1023合金复杂结构件等温锻造过程的数值模拟

The Study on Complex Titanium Alloy Components of Engine Isothermal Forging Deformation;

发动机钛合金复杂结构件等温锻造研究

Numerical simulation and experiment of isothermal forgings process of TC4 titanium alloy

TC4钛合金等温锻造过程的数值模拟和实验研究

Effect of Isothermal Forging on Distribution of Particles of SiC_p/Al Composites

等温锻造对SiC_p/Al复合材料颗粒分布的影响

Effects of Isothermal-forging on Microstructure and Properties of TC6 Titanium Alloy

等温锻造对TC6钛合金组织和性能的影响

Microstructures and Properties of TC17 Powder Metallurgy Titanium Alloy Prepared by Laser Sintering/Isothermal Forging

激光烧结/等温锻造TC17粉末钛合金的组织与性能

Effect of Strain Rate on Microstructure and Properties of Ti60 Alloy Under Isothermal Forging

等温锻造应变速率对Ti60合金组织和性能的影响

Simulation of Isothermal Forging for Superalloy and Analysis of Thermal Load on Die;

粉末高温合金盘件等温锻造模拟及模具热负荷分析

Deformation Character of Non-metallic Inclusions in Powder Superalloy During Isothermal Casting

粉末高温合金等温锻造过程非金属夹杂物的变形特征

forge a sword, a chain, an anchor, etc

锻造剑、 铁链、 锚等.