minimum yield strength

用法例句

Earthquake-resistant behavior of moment resisting frame with supplemental shear panels made of low yield strength steel;

本文探讨一种中间段以低屈服强度钢材为腹板，高强度钢为翼板，上下段皆以高强度钢制成之三段式剪力屈服型耐震间柱。

Effect of phosphorus on the yield strength of as-quenched GH761 alloy;

磷对GH761合金固溶水淬组织屈服强度的影响

Study of influence factors of yield strength of oil and gas pipeline;

油气管道屈服强度影响因素的研究

A modeling study of the yield strength of HRB335 hot rolled ribbed bar;

HRB335热轧带肋钢筋屈服强度模型研究

Based on the plain carbon steel with the chemical composition of 200MPa class steel the products of the yield stress of 400～500 MPa class and high-quality mechanical properties can be produced using the technology of chemistry tightly-tuning and controlled rolling - controlled cooling.

以屈服强度为 2 0 0MPa级的普碳钢为基本成分 ,采用成分微调与控轧控冷工艺相结合的技术路线 ,可将屈服强度提高到 4 0 0～ 5 0 0MPa,同时保证良好的综合性能。

From the tests, a two-stage linear relation has been found between yield stress(σ_s) and strain rate(ε),σ_s=σ_0+klgε.

对４种金属材料进行了应变率为１０~（－４）—１０~３ｓ~（－１）的拉伸试验，结果表明，屈服强度随应变率的升高分两阶段线性升高。

Properties of Low Yield Point Steels Used for Earthquake Resistant Buildings

建筑抗震阻尼器用低屈服强度钢的性能

Study on Increasing Yield Strength of Q345B Plate in JISCO;

提高酒钢Q345B板材屈服强度研究

Research on dynamic yield strength of steel 30CrMnSiNi2A

30CrMnSiNi2A钢的动态屈服强度研究

Analysis of Cracking During Stamping of 700MPa Grade Super High Strength Beam Steel

屈服强度700MPa级超高强度大梁钢冲压开裂分析

Influence of strength of ferrite matrix on yield strength of granular structure steels

铁素体基体强度对粒状组织钢屈服强度的影响

Development of High Strength and Low Yield Ratio Steel Plates for Buildings

高强度低屈强比建筑用钢板的研究开发

The Influence of Steel Bar Yield Strength Error to Structure Design;

钢筋屈服强度的误差对结构设计的影响

Effect Factors Analysis on Measuring X80 Grade Pipeline Steel Yield Strength

X80级管线钢管屈服强度测量影响因素的分析

Analysis of Unqualified Strength of 20MnSiV Hot Rolled Ribbed Bars

20MnSiV热轧带肋钢筋屈服强度不合原因分析

Effect of residual stress on yield strength of air-cooled bainitic steel

空冷贝氏体钢的残余应力对屈服强度的影响

Yield criteria applicability analysis of high strength hot rolled steel

屈服准则用于高强度热轧钢板的适用性分析

Research and Analysis of Abnormal Yield Strength During Tensile Test for Pipeline Steel

管线钢拉伸试验中异常屈服强度研究与分析

Analysis and improvement of yield strength disqualification of hot-rolled steel bar GR60

热轧GR60钢筋屈服强度不合格分析与改进

Effects of Heat-treatment Technology on the Yield-Strength of A356 Wheel by Low-Pressure Casting;

热处理工艺对A356低压铸造轮毂屈服强度的影响

Causes of Cracking during Stamping of 700MPa Ultra-high-strength Beam Steel

屈服强度700MPa级超高强度大梁钢冲压开裂原因的分析

Welding Properties of BLY225 Low Yield Strength Steel Developed by Baosteel

宝钢低屈服点钢BLY225的焊接性能

"Yield strength 85Kg/mm2(120,000psi)maximum"

屈服强度最大85Kg/mm2(120000psi)

The welder shall be capable of welding (full hard cold-rolled) steel with yield strength of up to 85Kg/mm2.

焊机应能焊(冷轧全硬)其屈服强度大于85Kg/mm2的钢带。