modulus in torsion

用法例句

This paper investigate the tensile performance of different kinds of structural sealants, the influence of water-ultraviolet radiation on tensile performance and the relation between tensile modulus and performance by testing the tensile performance of several structural sealants for insulating glass uni

通过对几种常用中空玻璃结构密封胶的拉伸黏结性能测试,研究不同类型的结构密封胶的拉伸黏结性能、水-紫外线对拉伸黏结性能的影响、拉伸模量与拉伸黏结性能的关系。

Results show that the mechanical properties including tensile strength,tensile modulus,flexural modu.

实验结果表明,采用偶联剂处理晶须可改善其填充UP树脂浇注体的拉伸强度、拉伸模量、弯曲模量和冲击强度。

Based on the finite element method,this paper presents a discussion on the influence of geogrid tensile modulus and frictional coefficient on.

应用有限单元法探讨筋材拉伸模量、筋土界面摩擦系数对一土工格栅加筋柔性路面的接触面剪切特性和基层回弹应变、塑性应变沿加载中心线分布的影响。

The influences of high temperature heat treatment condi-tion on orientation degree and its relation to tension modulus have been discussed.

本文采用单色Ｘ射线透射平板照相法，测定了ＰＡＮ基炭纤维高温热处理后其内部石墨微晶的取向度，讨论了高温热处理条件对取向度的影响，以及取向度与抗拉模量的关系。

Analysis on different modulus in tension and compression for piled rafts

拉压模量不同理论在桩筏基础分析中的应用

Analysis on Elastoplastic of Thick Spherical Shell with Different Modulus of Tension and Compression

不同拉压模量厚壁球壳的弹塑性分析

The Solution of Elasticity Theory with Different Modulus in Tension and Compression and Settlement Calculation of Piles;

拉压模量不同弹性理论解及桩基沉降计算

Analysis on different modulus in tension and compression for piled rafts

拉压模量不同理论在桩筏基础分析中的应用

Spherical cavity expansion in dilatant soils with different tension and compression moduli

拉压模量不同的剪胀土体中的球孔扩张问题

QUANTIFICATION INDEX RESEARCH FOR THE RATIONALITY OF STRUT-AND-TIE MODEL

拉-压杆模型合理性量化评价指标研究

Study on Nonlinear Mechanics Behavior of Elastic Structure with Different Tension and Compression Moduli;

拉压不同模量弹性结构的非线性力学行为研究

Analysis on the Deformation of Cylinder in Perfectly Plastic Material with Different Elastic Modulus in Tension and Compression

材料拉压不同模量及理想塑性的圆筒变形分析

Comparison of HMA Dynamic Moduli between Indirect Tension and Uniaxial Compression Test Modes

间接拉伸与单轴压缩模式沥青混合料动态模量比较分析

Results show that co-braided optical fibers have just a small quantity of effect on the elastic modulus of the braided composites.

结果表明光纤的编入对材料的拉伸弹性模量和压缩弹性模量影响也较小。

The micropore content was measured by mercury porosimeter.

用压汞法测定了拉伸丝的微孔含量。

The Design of Spring Draw and Pressure Power Measurement System Based on LabVIEW;

基于LabVIEW的弹簧拉压力测量系统设计

A minimum of 3 years experience in stamping design.

3年以上冲压与拉伸模具的设计经验。

Drawing of Cold Stamping Process of Bearing Frame and Die Design

轴承架的冷冲压拉深工艺及模具设计

Analytical model of predigested strut and tie model for shear-wall

基于STM的简化拉压杆剪力墙单元模型

Strut-and-tie Model of Deep Beam Design Under Uniform Distributed Loads

均布荷载下深梁设计的压杆-拉杆模型

Composite Extrusion Technics and Mould Design of Alumium Alloy Tie Bar

铝合金拉杆复合挤压工艺及模具设计

The Numerical Simulation of Blank Hold Force of Cylinder Part Drawing Based on Dynaform

基于Dynaform的圆筒件拉深压边力数值模拟

EXAMPLE OF DESIGN OF FLOATABLE AND WITHDRAW TYPE DIE INCLUDING CAVITY DIE, CORE ROD AND DIE SLEEVE

阴模、芯棒和压模套均可浮动的拉下式压模设计实例