pedestal cap

用法例句

Analysis of two types of central bearing seats of pumping units;

抽油机中央轴承座2种形式的分析

Based on the process improvement of bearing seat and numerical forming simulation,the rational project and the best process parameters were established.

通过对轴承座零件的工艺改进和成形数值模拟,最终确定了合理工艺方案和最佳成形参数,并在生产实践中得以验证,达到了节约成本,提高生产率的目的。

By means of spectrum analysis technology,the article inspects and diagnoses centrifugal compressor unit,analyzes the vibration features of compressor shell,rotor and bearing seat,finds out abnormal vibration and logical connection among vibration features in three position,according to the rotor unbalance conclusion,main- rains the unit,recovers normal operation of the unit.

利用频谱分析技术,对离心式压缩机机组进行状态监测和诊断,分析压缩机机壳、转子、轴承座的振动特征,查找振动异常的原因及三个部位振动特征间的逻辑联系,根据转子不平衡结论,对机组进行维修,恢复了机组的正常运行。

The detail forced status of the shaft of the overturn frame in the bearing chock overturn device has been described in this article,meanwhile the calculation review has been performed to the shaft rigidity after the structure upgrading finished.

针对某轴承座翻转装置中翻转架转轴的具体受力状况进行分析,并对改进结构后的转轴刚度进行计算校核。

In this paper,the authors analyzed by energy stable method that the stability of bearing chock of work roll about 2200mm high speed aluminum foil mill under two different restrict conditions which the gaps between bearing chock and bousing window are given or not.

用能量稳定法对 2 2 0 0mm高速铝箔轧机辊系中工作辊轴承座同机架窗口侧向有隙或无隙两种不同约束条件下的稳定性进行了分析。

The heat distortion of workroll bearing chock of 2050mm hot strip rolling mill employed in Baoshan continuous rolling mill is studied using finite element method(FEM),3D FEM temperature distribution program and SAP5 software.

以宝钢 2 0 50热连轧机工作辊轴承座的热变形故障作为研究对象 ,详细分析了轴承系统的内热源 ,确认轴承内部的摩擦热是轴承系统温升的主要热源 ,本文采用有限元方法 ,同时利用三维有限元温度场程序和SAP5软件 ,研究了轴承座的热变形场分布规律。

Hydraulic System Design of Disassembly and Assembly Device for Huge Roller Bearing;

大型轧辊轴承座拆装机液压系统设计

The authors described in detail the development of the new bearing, which can enlarge the moment, using dynamics analyses of the structural principle.

全面介绍了强化型管口轴承座的研制工作,进行了初步结构原理的动力学分析,并且测试了数种不同结构参数的轴承座的工作力矩特性。

The position and the appearance characters of the crack of bearing had been confirmed through testing experiment.

通过检验分析确定了轴承座裂纹的位置与形貌特征,分析了轴承座裂纹产生的原因,探讨了解决裂纹的措施。

plain bearing housing with bearings

装有轴承的普通轴承座

housing bearing plain without bearings

未装轴承的普通轴承座

Rolling bearings accessories--Plummer block housings--Boundary dimensions

GB/T7813-1998滚动轴承附件轴承座外形尺寸

housing for ball-, roller or needle roller bearings, not incorporating a bearing

未装轴承的滚珠、滚柱或滚针轴承座

alignment of bottom casing and bearing seating

下汽缸和轴承座找正

bracket incorporating a bearing housing or designed to house a bearing [incorporating ball or roller bearings]

装有轴承座或设计放置一个轴承[装有滚珠或滚柱轴承的托座]

bracket incorporating a bearing housing or designed to house a bearing [not incorporating ball or roller bearings]

装有轴承座或设计放置一个轴承,未装有滚珠或滚柱轴承的托座

chair, incorporating a bearing housing or designed to house a bearing, not incorporating ball-or roller bearings

装有轴承座或设计放置一个轴承,未装滚珠或滚柱轴承的座

main bearing aligning gauge

主轴承座孔同轴度检验仪

Rolling bearings--Housings for insert bearing boundary dimensions

GB/T7809-1995滚动轴承外球面球轴承座外形尺寸

housing for ball-, roller or needle roller bearings, incorporating a bearing

装有一个轴承的滚珠、滚柱或滚针轴承座

Analysis of the cooperation with Cork Drum Shaft,Bearing housing and Ball Bearing on the Changcheng Cigarette|machine

长城机水松纸鼓轮轴和轴承座孔与轴承之间配合关系的分析

Study on decaying of shock vibration energy during transmission through multi-interfaces in gear-shaft-bearing-housing system

冲击振动能量通过“齿轮-轴-轴承-轴承座”多界面传递损耗研究

Design and Simulation of Fracture Splitting Machine Tool for Bearing Bracket of Engine Crankcase

发动机缸体曲轴轴承座裂解机床设计及仿真

Numerical analysis on fracture splitting technology of main bearing block of engine

发动机曲轴箱轴承座裂解加工数值分析

Stress Analysis of Mill Bearing Chock Based on ABAQUS

基于ABAQUS的轧辊轴承座应力分析

Method and Application of Process Optimization for Backup Roll Chocks;

支承辊轴承座工艺优化设计方法与应用

Measurement of Dynamic Stresses and Temperatures of Main Bearing Walls and Caps on an Engine Block

发动机缸体主轴承座及主轴承盖的动态应力和温度测量