pull off

用法例句

Injection mould with ball screw stripping and ball bearing and ta-pered wedge fixed-distance pull off mechanism;

带滚珠丝杠脱模及滚珠斜楔拉模定距装置的注射模

The methods for producing special shaped steel wire are drawing by die or roller,rolling and combined method,whose characteristics and application are introduced.

生产异型钢丝的方法有模拉法、辊拉法、轧制法及组合法。

This paper investigate the tensile performance of different kinds of structural sealants, the influence of water-ultraviolet radiation on tensile performance and the relation between tensile modulus and performance by testing the tensile performance of several structural sealants for insulating glass uni

通过对几种常用中空玻璃结构密封胶的拉伸黏结性能测试,研究不同类型的结构密封胶的拉伸黏结性能、水-紫外线对拉伸黏结性能的影响、拉伸模量与拉伸黏结性能的关系。

Results show that the mechanical properties including tensile strength,tensile modulus,flexural modu.

实验结果表明,采用偶联剂处理晶须可改善其填充UP树脂浇注体的拉伸强度、拉伸模量、弯曲模量和冲击强度。

Based on the finite element method,this paper presents a discussion on the influence of geogrid tensile modulus and frictional coefficient on.

应用有限单元法探讨筋材拉伸模量、筋土界面摩擦系数对一土工格栅加筋柔性路面的接触面剪切特性和基层回弹应变、塑性应变沿加载中心线分布的影响。

TopSolid-based rapid design system of drawing die for automotive sheet covering;

基于TopSolid的汽车覆盖件拉深模快速设计系统研究

Design and test run of drawing die for loudspeaker basket;

扬声器盆架拉深模设计与调试

Die face design of drawing die for automobile panel;

汽车覆盖件拉深模型面设计

Wire、bar or tube drawing dies--As sintered pellets of hard metal

GB/T6883-1995线、棒和管拉模用硬质合金模坯

A die plate for flattening metal into strips, as in the manufacture of watch springs.

扁条拉模一种用来拉平钢条的模板，如用于生产手表发条的模板

Clara was full of a sombre preconception.

克拉拉心中充满了模糊的成见。

Euler-Euler Method Simulating Pulsed Fluidized Bed Behaviors

欧拉—欧拉法脉动流化床运动行为模拟

Analysis of the Wire Drawing Testing of Copper Bar Drawer and the Selecting of Die

铜大拉机拉线试验及模具选择的分析

Modal Test and Analysis of Cable-Stayed Bridge Used with CFRP Stay Cables

CFRP拉索斜拉桥模态试验与分析

die ,wiredrawing (incl radioactive)

拉丝模（包括放射性的）

diamond die polishing machine

金刚石拉丝模抛光机

Satires after Horace.

模仿贺拉斯的讽刺作品

flexible die lips, push &pull adjustable

活动式模唇,可推拉调节；

Draw forming simulation and die-structure optimization of front fender

翼子板拉深成形模拟及模具结构优化

Experimental Modal Analysis of Cable-stayed Arch Bridge Model and Research on the Influences of Cable on Modal Parameters;

斜拉拱桥模型试验模态分析及拉索对模态参数影响研究

The Development of Aquadag Used on Multi- Die Drawing Machine for Drawing Fine Tungsten Wire

多模拉丝机拉制细钨丝用石墨乳的研制

Numerical Simulation of Breadthwise Stretching Process of Biaxially Oriented Plastics Film;

双向拉伸塑料薄膜横拉成型的数值模拟研究

Imporvment on the Pulling Processs and the Polarization Dependent Loss of 1X2 Fiber FBT Couplers

1X2单模融拉型光纤耦合器拉锥工艺与PDL的改进

Model Test on the Cable-beam Anchorage Structure with Tensile Anchor Plate of Cable-stayed Bridges

斜拉桥锚拉板式的锚固结构模型试验与研究

Research on Dynamic Simulation Methodology for Cable Loss of Cable-Stayed Bridges

斜拉桥拉索断裂损伤的动力过程模拟方法研究

Research on cable damage identification of cable-stayed bridges based on modal strain energy index

利用模态应变能指标的斜拉桥拉索损伤识别