pull shaft

用法例句

Discussion of Double Raceway Dynamic Grinding Method on Top Roller Bearing Out Ring

上罗拉轴承外圈双滚道动态磨削方法的探讨

Calculation is done of the radial clearance of the top roller bearing SL1-6918 to determine the clearance range.

对SL1-6819型上罗拉轴承进行了径向游隙的计算,以便确定游隙的范围;分析了上罗拉轴承的结构和上罗拉轴承的游隙在实际使用状况下的存在形式及对轴承运转的重要作用;提出了影响成纱质量的关键因素。

Sampling the top roller bearing SL series,details introduction is done to the quality norm.

以SL系列上罗拉轴承为例,详细介绍了其质量标准,从清洗、套胶管和润滑3个方面阐述了上罗拉轴承的使用及保养。

The fatigue tests on axial tension an d tension-compression under consta nt amplitude cyclic loading have been carried out on plain concrete in this paper against the fatigue state of te nsion-compression in prestressed c oncrete bridges,and the test results are compared with those obtained by other researchers and code for design.

本文针对预应力混凝土桥梁工程中遇到的拉-压疲劳状态,进行了76个混凝土试件在等幅重复荷载作用下的轴拉、拉-压疲劳试验。

Discussion of Double Raceway Dynamic Grinding Method on Top Roller Bearing Out Ring

上罗拉轴承外圈双滚道动态磨削方法的探讨

Impact Analysis of the Ring Slot around the Bearing Shell of Top Rollers on Cot Telescoping Process

上罗拉轴承外壳环形槽对套制胶辊的影响分析

Application of Self-lubricating Roller Bearing in Spinning Frame

含油自润滑罗拉轴承在细纱机上的应用

Provide manufacture services of rubber-ware pressing process machine, roller bearing oiling, rubber-ware grinding and cutting.

提供皮棍压套罗拉轴承加油皮棍磨削加工服务。

upper center crankshaft bearing

曲轴主轴承上中轴瓦

Remove the lower insert from the bearing cap.

从轴承盖上拆去下轴瓦。

The journal rubs against the bearing surface.

轴颈在轴承面上摩擦。

Remove thrust bearings from rear main bearing carrier.

从后主轴承托架上拆下止推轴承。

Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.

曲轴上的导向轴承:曲轴上的导向轴承一般或者是轴瓦,或者是球轴承。

Excessive friction in strut upper bearing

支柱上轴承磨损过度

governor upper bush

调速器上部轴承衬套

radial bearing upper drive sub

上部径向轴承传动接头

The carriage is supported on guide shafts.

托架支承在导轴上。

Schromberg alloy

施罗姆伯格锌基轴承合金

Pull vibration damper off of the crankshaft.

将减震器从曲轴上拉下。

Drawing of Cold Stamping Process of Bearing Frame and Die Design

轴承架的冷冲压拉深工艺及模具设计

Shaft Assembly (Male, female, washer, grease….

轴组件（轴，轴套，轴承，油脂。。。）

RUGGEDNESS. Automotive ring gear differential. Axle shafts on roller bearings.

强度：自动差速齿轮，滚子轴承上的刚性车轴。