ring joint (RJ)

用法例句

Malleable cast iron pipe fittings--Type size--Parallel union gaskets

GB/T3289.39-1982可锻铸铁管路连接件型式尺寸平形活接头垫圈

A wide range of standard stampings, non-standard products, stainless steel washers, internal/ external teeth washers, rings, circlips for holes, circlips for shaft, other fasteners, fittings, seal washers and clamps主要生产各种标准件冲压件.各种非标产品.

不绣钢垫圈;内外齿垫圈;挡圈;孔用挡圈;轴用挡圈;纱嘴头,其他紧固件、接件密封垫圈卡圈.

Flared type tube fittings--Back-up washer

GB/T5652-1985扩口式管接头锁紧螺母垫圈

Bite type tube fittings--Tipping washer

GB/T3762-1983卡套式管接头用尖角密封垫圈

a ring for packing pistons or sealing a pipe joint.

填塞活塞或垫在导管接头的圈环。

With gasketed connections, the material of construction of the washer is important, both for compatibility with the gases in use and for its mechanical properties.

对于衬垫接头，垫圈的结构材料对于使用的气体的相容性和垫圈的机械性能都是很重要的。

Inspect the CV joints and front suspension component boots and seals.

检查CV接头和前悬吊部件保护罩和垫圈。

A gasketed connection has four parts: the valve outlet, a nipple, a nut, and a gasket (or washer).

一个衬垫接头有四个零件：一个阀门排气口、一个管接口、一个螺母和一个衬垫（或垫圈）。

" Hexagon head bolt, single coil spring lock washer and plain washer assemblies"

"GB/T9074.17-1988六角头螺栓,弹簧垫圈和平垫圈组合件"

tapped coil

多(接)头线圈, 抽头线圈

The tightening force required for gasketed connections is somewhat dependent on the washer material being used.

对于衬垫接头，所要求的上紧的力量稍微依赖于正在使用的垫圈材料。

It is essential to use a new gasket each time the connection is tightened because the softened nickel washer becomes hardened after each compression.

因为在每次压缩之后软化的镍垫圈会变硬，每次接头上紧时必须使用新衬垫。

master cylinder outlet fitting gasket

主缸出油接头垫密片

" Cross recessed pan head screw,single coil spring lock washer and plain washer assemblies"

"GB/T9074.4-1988十字槽盘头螺钉,弹簧垫圈和平垫圈组合件"

" Cross recessed small pan head screw,single coil spring lock washer and plain washer assemblies"

GB/T9074.8-1988十字槽小盘头螺钉和弹簧垫圈及平垫圈组合件

" Cross recessed hexagon bolt with indentation, single coil lock washer and plain washer assemblies"

"GB/T9074.13-1988十字槽凹穴六角头螺栓,弹簧垫圈和平垫圈组合件"

Remove bolts, nuts and washers attaching manifold to cylinder hea

拆下系附在汽缸头的螺栓，螺帽和垫圈。

Hexagon head bolt and plain washer assemblies

GB/T9074.14-1988六角头螺栓和平垫圈组合件