shaft arm

用法例句

Research application of precision forging process and die CAD/CAM of rocker shaft bed;

摇臂轴座精锻工艺及模具CAD/CAM研究应用

The paper analysis the forging craft of rocker shaft bed part, introduce the computing technology of high energy screw press apparent pressure value.

280柴油机摇臂轴座一改传统的铸造方法为精锻制造。

This paper specifies the characteristics of multi-stage centrifugal compressor with single-shaft overhang type of MCO series.

阐述了MCO系列单轴悬臂多级离心压缩机的特点,在同种设计参数条件下,该机与常规单缸压缩机设计方案相比,提高了工作效率,降低了运行成本;与常规双缸压缩机方案相比不仅降低了制造成本、运行成本,而且减少了故障点,使机组运转更安全稳定,更易维护。

The dynamic model of a 2B0 locomotive for export is built with software SIMPACK to analyze the influence of longitudinal position of the locating node for tumbler axle-box on locomotive dynamics.

利用SIMPACK建立某出口2B0机车动力学模型,分析了转臂轴箱定位节点的纵向位置对机车动力学性能的影响。

The article makes the finite element analysis to the turning arm bearing of the star wheel speed reducer by the ANSYS software.

本文应用ANSYS软件,对星轮减速器的转臂轴承组件进行有限元分析。

valve rocker shaft oil pipe adapter

气门摇臂轴油管接头

Research on Non-contact Measurement Technology of Two Axes' Parallel Error for Crankshaft;

曲臂两臂轴线平行度误差非接触检测技术研究

Install pitman shaft and side cover in the housing.

在机座中安装转向摇臂轴和侧盖。

Hardening Crack Analysis and Prevention Measurement for 45 SteelWobbling Arm Axis

45钢摆臂轴淬火裂纹分析及防止措施

Precise 3D Modeling of Design of Arm Shaft;

转向摇臂轴的精确三维造型设计应用

"Essentially, the steering gear consists of two parts, a worm on the end of the steering shaft and a pitmanarm shaft on which there is a gear sector, toothed roller, or stud."

转向器基本上由两部分组成:装在转向轴末端的蜗杆和转向摇臂轴。

engine supporting arm

发动机曲轴箱支座臂

Install the push rods, rocker arms, pivots and bridges in the order they were remove

按照拆卸顺序安装推杆、摇臂、枢轴和桥臂。

Effect of the Axle Box Rotary Arm Positioning Mode on Resilient Nodal Points

轴箱转臂定位方式对弹性节点的影响

The rollers are carried by an L - shaped lever, fixed to a horizontal shaft, which also carries short arms to which the reed and gripper guides are fixed.

转子装在l形杆上,l形杆固定在水平轴上。在水平轴上还装有短臂,钢筘和导梭片就装在短臂上。

Remove the upper suspension arm nut and bolt at the axle bracket.

从车轴支架上拆去上端悬吊臂螺帽和螺栓。

Remove the lower suspension arm nut and bolt from the axle bracket.

从车轴支架上拆去下端悬吊臂螺帽和螺栓。

The axial force is large in the cantilever, and it has some kind of偏心距?!

工程系：悬臂梁的轴压不小啊，还有点偏心距。。。。

Position the lower suspension arm at the axle bracket and rear bracket.

把下端悬吊臂放在车轴支架和后侧支架上。

Study on Oil Film-Roller Combination Bearing of φ200 Cantilever Finishing Mill;

φ200悬臂式精轧机油膜—滚子组合轴承开发研究

Stability of Monosymmetric I-section Cantilevers;

单轴对称工字形等截面悬臂梁的整体稳定性

Cantalever Vertical Axis Roadheader Bit Distribution Studying and Simulation;

悬臂式纵轴掘进机截齿分布研究及仿真

Reason Causing Blowhole in Headstock Housing of Radial Drilling Machine and its Prevention

摇臂钻床主轴箱体气孔产生原因及消除措施