去查网 logo

shaft position

中文翻译轴的位置

同义词释义

    1)shaft position,轴的位置2)axial position,轴向位置3)axle center position,轴心位置4)crankshaft position,曲轴位置5)optical axis position,光轴位置6)Rotational axis position,轴线位置

用法例句

    Influences of axial positions of grooved casing treatment on stall margin improvement;

    轴向位置变化对槽式机匣扩稳效果的影响

    This paper briefly introduces the electronic spray system working principle of inlet manifold absolute pressure sensor,crankshaft position sensor and synchronizing signal sensor on Kerokee engine It introduces the way of testing the trouble position,which is good for its operation and maintenanc

    对切诺基发动机电喷系统的进气歧管绝对压力传感器,曲轴位置传感器和同步信号传感器的工作原理进行了简要介绍,重点介绍了当这3种传感器发生故障时怎样去检测所在的故障部位,有助于使用和维修这种发动机。

    The dependence of the laser output power versus the laser output aperture and optical axis position on CW COIL;

    CW COIL输出功率与输出孔径及光轴位置之间的依赖关系

    situated away from the center or axis.

    处于远离中心或者轴的位置

    Create Explicit Key PositionY

    创建Y轴的位置直接关键帧

    Create Explicit Key Position X

    创建X轴的位置直接关键帧

    Create Explicit Key Position Z

    创建Z轴的位置直接关键帧

    "STAMP X&Y LOCATIONS, 0.10 characters"

    印上X和Y轴的位置,字高0.10

    Place the3 DCursor at the position through which the rotation axis must pass. Such an axis will be vertical.

    放置3D光标在你要作为旋转轴的位置,轴是垂直的。

    Research on Position Alignment Method of a Three-axis Simulator

    三轴转台三轴交汇中心位置对准方法的研究

    Measuring and Controlling the Position Error of Bearing Hole in Machining Canular Forked Shaft;

    叉头套轴承孔位置误差的测量与控制

    Design of a Position-Sensorless Controller for Axial Blood Pump;

    轴流式血泵无位置传感器控制的设计

    Application of CPLD in biaxial position detection system

    CPLD在双轴位置检测系统中的应用

    Calculation on Trunnion Position for a 220t High H/D Ratio Converter

    220t大高径比转炉耳轴位置的确定

    Effect of ejector axial position on performance of pulse detonation engine

    引射器轴向位置对PDE的性能影响实验

    Bushings: Furnishes shaft support at three locations for positive shaft alignment and actuator support.

    衬套:在三个位置上配置轴支撑,有利于轴校直和执行机构的支撑。

    Bushings (4): Furnishes shaft support at three locations for positive shaft alignment and actuator support.

    衬套(4):在三个位置上配置轴支撑,有利于轴校直和执行机构的支撑。

    Supplies the required 5 volt power source to the crankshaft position sensor, camshaft position sensor, MAP sensor and throttle position sensor.

    向曲轴位置感应器、凸轮轴位置感应器、MAP感应器以及节气阀位置感应器提供所需的5伏电压。

    axile:Situated along the central axis of an ovary having two or more locules:

    轴上的:位于沿着有两个或更多小室的子房的中轴线的位置的。

    Create a Position Key on

    创建Y轴位置关键帧

    Create a Position Key on X

    创建X轴位置关键帧

全部查询工具

关于我们免责声明联系我们网站地图最近更新

免责说明:本站为非营利性网站,本站内容全部由《去查网》从互联网搜集编辑整理而成,版权归原作者所有,如有冒犯,请联系我们删除。

Copyright © 2020 - 2024 quchaw.com All rights reserved.浙ICP备20019715号