small axle

用法例句

Because the area Ao of the end surface of the small axle is less than that of the heating section area ofthe conventional inductor of the high frequency induction hardening ,the end surface will be overheated or burnt at thecorner or underhardened at the centre due to skin effect and corner effect.

经高频端面淬火的小轴，因其端面面积小于传统的高频平面加热感应器的加热截面积，并由于集肤效应和尖角效应而容易造成轴端倒角附近区域组织过热过烧或端面圆心处硬度不足。

Material Selection and processing of small gear shaft in drilling pump;

钻井泵小齿轮轴的选材与加工

For resolving efficiently the problem of machining errors that are caused by bending deflection of weak stiffness shafts,this paper has analyzed machining errors of the workpiece by calculating the bending deflection based on reasonable selecting the technological parameters,and offered specific measures of error control——to compensate the errors by macro programming.

为了高效率解决小刚度轴的弯曲变形引起的加工误差问题,在合理选择工艺参数的基础上,通过弯曲变形量计算来分析工件的加工误差,并给出了具体的误差控制措施应用宏指令编程进行误差补偿。

Application of SUSAN operator in image segmentation of micro bearings surface defect;

SUSAN算子在微小轴承表面缺陷图像分割中的应用

End play in drive pinion bearings.

驱动小齿轮轴承的端隙。

differential drive pinion cage bearing

差速器主小齿轮轴承罩

wheel cylinder adjusting pinion shaft

轴闸储气筒调准小齿轮轴

Refer to Drive Pinion Bearing Pre-Load Adjustment.

参阅驱动小齿轮轴承预荷调整。

Rotate the pinion yoke three or four times.

旋转小齿轮轴轭三次或四次。

Remove the universal joint strap bolts at the pinion shaft yoke.

在小齿轮轴轴轭处拆卸万向节扣夹螺栓。

Hold the yoke with Wrench 67Remove the pinion shaft nut and washer.

用扳手6719握住轴轭。拆下小齿轮轴螺帽和垫圈。

Mark the propeller shaft and pinion yoke, or pinion flange, for installation reference.

在传动轴和传动轴轴轭、或小齿轮轴轭上作标记，作安装的参考标志。

Using a short piece of pipe and Holder 6958 to hold the pinion yoke, or pinion flange, remove the pinion nut and washer.

用短管和托架6958固定小齿轮轴轭或小齿轮凸缘，拆下小齿轮螺帽和垫圈。

axle drive pinion adjusting sleeve

车轴传动小齿轮调整套

motor-drive shaft and pinio

电动机传动轴和小齿轮

axle drive bevel pinion

车轴传动的小伞齿轮

drive pinion cone bearing

主动小齿轮锥形轴承

drive pinion cone bearing cup

传动小齿轮锥形轴承杯

differential pinion cross

差速器小齿轮十字轴

fine pitch automatic pinion shaft hobbing machine

小模数轴齿轮自动滚齿机

twin-input single-output gear

双主动齿轮单出轴齿轮

Install pinion front bearing, if necessary.

如需要，安装小齿轮前轴承。