bearing hole

用法例句

Clamp on cutting bearing hole of coal car wheel;

煤车轮轴承孔粗精车定位夹紧机构

It is very important to measure and control the position of bearing hole when machining canular forked shaft.

在叉头套加工过程中,轴承孔位置误差的测量和控制是十分重要。

Fracture behavior of bearing hole on supporting bar was analyzed using scanning electron microscope(SEM) and energy dispersive spectroscopy(EDS).

用扫描电镜和能谱仪对支撑杆轴承孔断裂原因进行分析。

In order to mount the separating glide bearings, the locating slot is designed on bearing bores, but the center of milling is difficult to adjust when working.

为便于安装剖分式滑动轴承,在机体的轴承孔上,必须设有定位槽,在加工定位槽时,难于调整铣刀中心,而且费工费时。

Based on three-dimensional coupled thermo-mechanical finite element analysis,with the help of FEM software(ANSYS), temperature field and displacement field of thermal deformation of bearing borizing are given.

利用ANSYS软件对铝箔轧机的工作辊轴承座进行热-力耦合的三维有限元分析,给出了轴承座的温度场及其热变形,根据有限元的分析结果,提出了改进轴承镗孔结构的设计方法。

The system is based on the air-electric sensor technology,which can automatically measure cylinder hole and main bearing hole of the cylinder block,make grouping and marking and meet high precision measure requirements.

工业计算机控制的发动机缸体测量系统是由气动测量芯轴和差压式测量回路等组成,系统采用气电转换技术,在线自动测量发动机缸孔和主轴承孔并分组打号,满足了生产现场高精度测量的要求。

It′s always one of the difficulties to machine main bearing holes on bedplate for large bore diesel engines.

大缸径柴油机机座主轴承孔的加工技术一直是柴油机制造的一大难点 ,现提出了采取的一系列工艺技术措施 ,解决了柴油机生产中的这一关键技术问题 ,提高了大缸径柴油机机座主轴承孔的制造水

Taking the correction of the gear shaft and bearing saddle bore of a reducer as the example, this paper probes into the problem of the correction of the gear shaft and bearing saddle bore often encountered in the inspection of e lectromechanic equipment, and according to the practical experiences, makes emph atically discussion on the brush plating repair technique.

以某减速机齿轮轴与轴承座孔的修复为例,对机电设备检修工作中经常遇到的齿轮轴和轴承座孔修复问题进行了探讨,并根据实践经验对刷镀修复工艺要点进行了重点论述。

Measuring and Controlling the Position Error of Bearing Hole in Machining Canular Forked Shaft;

叉头套轴承孔位置误差的测量与控制

The influence of the journal misalignment in bearing bore resulted from crankshaft deformation when it acted by load should be considered in the lubrication analysis of crankshaft bearing.

曲轴轴承的润滑分析应该考虑曲轴受载变形导致轴颈在轴承孔中倾斜的影响；

Design of Roundness Automatic Measuring System for Bearing Hole of Diesel Engine

机车柴油机轴承孔的圆度自动检测系统设计

main bearing aligning gauge

主轴承座孔同轴度检验仪

Analysis of the cooperation with Cork Drum Shaft,Bearing housing and Ball Bearing on the Changcheng Cigarette|machine

长城机水松纸鼓轮轴和轴承座孔与轴承之间配合关系的分析

Measures for improving the concentricity of the bearing s minor hole at the two ends;

提高套筒两端轴承档内孔同轴度的措施

Deformation of Porous Pad of an Aerostatic Porous Thrust Bearing

空气静压多孔质止推轴承多孔质圆板的变形

Internal Bore Processing of Precision Miniature Bearings Based on Spark Grinding

基于电火花磨削的精密微型轴承内孔加工

Relative Factors Affecting Static Performance of Aerostatic Porous Bearings

影响空气静压多孔质轴承静态性能的有关因素

The Study of Oil-impregnated Porous Polyimide Retainers Used for Gyroscope Bearing;

陀螺轴承用多孔含油聚酰亚胺保持架研究

Research on Key Technologies of Partial Porous Externally Pressurized Gas Bearing;

局部多孔质气体静压轴承关键技术的研究

Theoretic and Experimental Investigation on the Aerostatic Porous Bearing

多孔质气体润滑轴承设计理论与实验方法

Investigation of Pressure Distribution of Partial Porous Aerostatic Thrust Bearing

局部多孔质气体静压止推轴承压力分布的研究

Research the Bearing Capacity of Universal-joint Spindle in 170 Piercing Mill Main Transmission System

170穿孔机主传动系统万向接轴承载能力分析

Research on the Dimension Compensation of the Bearing and the Shell Holes Mate with the Temperature Rising

壳体孔与轴承配合的温升尺寸补偿研究

Analysis of the Precision Measure Method for the Bearing Seat Hole Center Distance in the Gear Box

齿轮箱轴承座孔的中心距测量方法精度分析

Determination of contact-angle searching field on high-speed ball bearing in drilling equipment

钻孔设备高速滚珠轴承接触角搜索域的确定

First you need the boring for the shaft, then install the stern tube into the stern frame, next fit the gun-metal or white-metal bush.

首先要镗孔，然后安装尾轴管，接下来装炮铜或白合金制的轴承套，也叫轴承。