welded bonnet (WB)

用法例句

Welding standard research in manufacturing of the valve;

阀门焊接相关标准的讨论

Stress calculation and analysis on welding seat of stop valve;

截止阀焊接阀座的应力计算与分析

Valves should not be assembled to the flanges and then welded into the piping system.

不要把组装上法兰的阀门焊接到管道系统上。

"Face-to-face, centre-to-face, end-to-end and centre-to-end dimensions of valves--Buttwelding valves"

GB/T15188.1-1994阀门的结构长度对焊连接阀门

General purpose industrial valves--Flanged and butt-weld end steel ball valves

GB/T12237-1989通用阀门法兰和对焊连接钢制球阀

General purpose industrial valves-Flanged and butt-weld steel gate valves

GB/T12234-1989通用阀门法兰和对焊连接钢制闸阀

TFE disc valves limite to450 oF temperatures.

焊接连接端口阀门温度限制在不影响焊接连接端口的强度范围内。

When installing solder end valves, conventional soldering techniques should be used.

安装焊接连接端口的阀门时，应该采用普通焊接技术。

ADJUSTED PRESSURE/ TEMPERATURE RATINGS FOR JOINTS MADE OF COPPER TUBE AND SOLDER END VALVES?

在连接铜管和焊接端口阀门时要核对压力/度额定值?

ADJUSTED PRESSURE/TEMPERATURE RATINGS FOR JOINTS MADE OF COPPER TUBE AND SOLDER END VALVES?

在连接铜管和焊接端口阀门时要核对压力/温度额定值?

Assessing the safety of fully welded body pipeline ball valve

全焊接阀体管线球阀焊接接头的安全评估

Leaving the valve in a fully closed position helps prevent weld spatter from falling directly onto the mating faces of the seats.

保持阀门处于完全关闭状态，有助于防止焊花飞溅直接落到阀座连接面上。

" Face-to-face, centre-to-face, end-to-end and centre-to-end dimensions of valves--Wafer valves"

GB/T15188.2-1994阀门的结构长度对夹连接阀门

Welded-in seat is Stellite 6 faced.

焊接连接阀座采用钨铬钴合金6阀座面。

High quality stainless pipe valve and seamless welded joint can ensure absolutely air conurbation and durability of pipe system.

高品质不锈钢的管道阀门，无缝焊接的连接口，以保证绝对的气体密闭性和管道系统的耐用性。

apply brazing wire or rod at point where tube enters valve socket.

将焊线或焊杆点在阀门里的管道套座上。

Study on Wear Resistance of the Electrodes of Cr13 Alloy System for Valve Sealing Surface;

Cr13系阀门密封面堆焊焊条耐磨性的研究

New Stainless Steel Heap Welding Technique for Main Steam Valve Sealing Suface

主蒸汽阀门密封面不锈钢堆焊新工艺

Care must be taken not to overheat and damage valves during the soldering process.

在焊接过程中,必须要小心谨慎,避免由于温度过高导致阀门受到损害。

General purpose industrial valves-Flanged and wafer butterfly valves

GB/T12238-1989通用阀门法兰和对夹连接蝶阀